Forums
New posts
Articles
Product Reviews
Policies
FAQ
Log in
Register
What's new
Search
Search
Search titles only
By:
New posts
Menu
Log in
Register
Install the app
Install
Forums
Apple Computing Products:
macOS - Notebook Hardware
Put your iBook on steroids...
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="DanielNTX" data-source="post: 164581" data-attributes="member: 10066"><p>So I went out and did it. I purchased a current stock iBook 12" and cracked it open. They are definitely not user friendly for upgrades compared to the likes of Dell/IBM/HP where everything is modular and can be accessed from the outside easily. I removed about 30 to 40 screws to access everything.</p><p></p><p>I put in 1 gig of Crucial PC2700 ram, a Pioneer DVR-K05 8x8 Slim DVD Rewritable Drive (recognized as Apple installed/supported in OS X 10.4), and a FUJITSU MHV2080AH 80GB 5400RPM 8MB Cache hard disk.</p><p></p><p>The notebook cost me $900, the memory $109, the DVD drive $85 ad the hard disk was $110 for a total of $1204 shipped & no taxes.</p><p></p><p>For the Pioneer burner to fit, I had to modify the slot bezel from the combo drive by breaking out my dremmel tool and sanding off two small nipples that prevented the bezel from sitting flush with the new drive.</p><p></p><p>I also made a boo-boo when removing the top casing from the iBook... I accidently ripped of the connector jack off the system board for the right speaker. I was being over zealous removing the cables that were connected to the system board. I should have been more careful using needle nose pliers to detach the cables instead of my fingers. Anyways, after being pissed and getting over my stupidity, I broke out the soldering iron (with micro fine tip) and heated it up and then soldered the jack back in place. I did a quick test by booting the system up with the top casing and keyboard back together to see if the speaker would work again and luckily it did. Then I removed everything and installed the DVD drive and then the hard disk.</p><p></p><p>I would say the whole thing took me about 4 hours including reinstalling OS X. The hardest two things besides my mistake is removing the bottom casing (I used an old credit card) and keeping track of where all the screws go because they are different sizes and lengths.</p><p></p><p>Overclocking a Mac mini is much easier then these upgrades. As a comparison, I rate the difficulty of oc'ing a Mac mini 3 or 4 out of 10 and the upgrading of an iBook a 6 or 7 out of 10 (make that a 7 or 8 if you accidently rip off a connector jack from a system board).</p><p></p><p>Good luck to anyone who attempts this.</p><p></p><p>I was almost tempted to figure out how to change the bus speed from 133 to 142MHz, but decided against it because I couldn't find any information on the resistor settings on the internet. The clock multiplier is alreadly locked at 10X which is pretty high, but I bet it would be pretty easy to bump the bus speed from 133 to 142MHz to be like it's bigger 14" brother.</p></blockquote><p></p>
[QUOTE="DanielNTX, post: 164581, member: 10066"] So I went out and did it. I purchased a current stock iBook 12" and cracked it open. They are definitely not user friendly for upgrades compared to the likes of Dell/IBM/HP where everything is modular and can be accessed from the outside easily. I removed about 30 to 40 screws to access everything. I put in 1 gig of Crucial PC2700 ram, a Pioneer DVR-K05 8x8 Slim DVD Rewritable Drive (recognized as Apple installed/supported in OS X 10.4), and a FUJITSU MHV2080AH 80GB 5400RPM 8MB Cache hard disk. The notebook cost me $900, the memory $109, the DVD drive $85 ad the hard disk was $110 for a total of $1204 shipped & no taxes. For the Pioneer burner to fit, I had to modify the slot bezel from the combo drive by breaking out my dremmel tool and sanding off two small nipples that prevented the bezel from sitting flush with the new drive. I also made a boo-boo when removing the top casing from the iBook... I accidently ripped of the connector jack off the system board for the right speaker. I was being over zealous removing the cables that were connected to the system board. I should have been more careful using needle nose pliers to detach the cables instead of my fingers. Anyways, after being pissed and getting over my stupidity, I broke out the soldering iron (with micro fine tip) and heated it up and then soldered the jack back in place. I did a quick test by booting the system up with the top casing and keyboard back together to see if the speaker would work again and luckily it did. Then I removed everything and installed the DVD drive and then the hard disk. I would say the whole thing took me about 4 hours including reinstalling OS X. The hardest two things besides my mistake is removing the bottom casing (I used an old credit card) and keeping track of where all the screws go because they are different sizes and lengths. Overclocking a Mac mini is much easier then these upgrades. As a comparison, I rate the difficulty of oc'ing a Mac mini 3 or 4 out of 10 and the upgrading of an iBook a 6 or 7 out of 10 (make that a 7 or 8 if you accidently rip off a connector jack from a system board). Good luck to anyone who attempts this. I was almost tempted to figure out how to change the bus speed from 133 to 142MHz, but decided against it because I couldn't find any information on the resistor settings on the internet. The clock multiplier is alreadly locked at 10X which is pretty high, but I bet it would be pretty easy to bump the bus speed from 133 to 142MHz to be like it's bigger 14" brother. [/QUOTE]
Verification
Post reply
Forums
Apple Computing Products:
macOS - Notebook Hardware
Put your iBook on steroids...
Top