Help! I'm confused with bridge mode vs AP mode.

Joined
Jan 2, 2009
Messages
156
Reaction score
0
Points
16
I'm trying to connect my D-Link DIR-880L to my main router to basically extend the reach of my wireless signal. I have an ethernet cable that I'm able to connect to my main router via a switch placed in my master bedroom closet which is the hub of all the network cables.

I'm hoping someone can help me because it seems that the information I'm reading on the internet has one person saying one thing and another person saying something else. Go figure, right? So the DIR-880L has mode in the setup called router mode or bridge mode and I don't believe bridge mode is what I'm looking for. Please correct me if I'm wrong but isn't bridge mode a way to extend a wireless signal but in order to do this, the DIR-880L has to be within reach of the main router because it takes the signal of the main router to connect to the network and from there pushes the signal out via the antennas of the DIR-880L? I've also read that although this works, it's not the most ideal because it will slow the clients connected to the DIR-880L because some of the data is basically being used to transmit data from the client to the DIR-880L and then some of the other data is being used to transmit data from the DIR-880L to the main router.

So if I'm understanding this correctly, I don't want this setup because I want to use the ethernet cable to connect to the main router, via the switch. The problem with this is, the DIR-880L doesn't have an Access Point mode, which is what I've read that I need. I've found some extenders that appear to have the router, bridge, and access point mode built into the set up options but the DIR-880L doesn't have this option. So I found that you basically need to turn off DHCP server. Is this all I need to do to accomplish what I want or is it more involved?

Also, if this works, can someone confirm that I would then be able to connect other clients via ethernet cables to the DIR-880L and via wireless or can the client only be connected via wireless? I ask because again, I'm reading conflicting information. Some say if you do it this way, you can only connect additional clients wirelessly. The other thing that throws me off is that I've read that if I connect it as an access point, the ethernet cable from the main router (via switch) must be connected to the DIR-880L using one of the LAN ports and NOT using the WAN port.

I know. Many questions but I'm confused so hoping someone can help me figure this out. Thanks.
 

Slydude

Well-known member
Staff member
Moderator
Joined
Nov 15, 2009
Messages
17,596
Reaction score
1,072
Points
113
Location
North Louisiana, USA
Your Mac's Specs
M1 MacMini 16 GB - Ventura, iPhone 14 Pro Max, 2015 iMac 16 GB Monterey
If I am understanding what you want to do correctly you do indeed want to put the DIR-88L into bridge mode. You already have one router on the network that hands out IP addresses for your devices. If you configure the D-Link as a router you will now have two divices handing out IP addresses and that will cause conflicts. Bridge mode can usually be used in either wired or wireless mode although an old device I had used to shut down the wired ports when in brige mode.

I'm looking for a good set of directions for putting the 880L innto bridge mode. The directions I have found so far seem to assume that you are going to do that wirelessly.My understanding is you want to make the connection byehternet wire cirrect?
 
OP
H
Joined
Jan 2, 2009
Messages
156
Reaction score
0
Points
16
If I am understanding what you want to do correctly you do indeed want to put the DIR-88L into bridge mode. You already have one router on the network that hands out IP addresses for your devices. If you configure the D-Link as a router you will now have two divices handing out IP addresses and that will cause conflicts. Bridge mode can usually be used in either wired or wireless mode although an old device I had used to shut down the wired ports when in brige mode.

I'm looking for a good set of directions for putting the 880L innto bridge mode. The directions I have found so far seem to assume that you are going to do that wirelessly.My understanding is you want to make the connection byehternet wire cirrect?

Yes, I do want to connect it via ethernet. So my understanding is that when connecting via bridge mode, some of the bandwidth is being used to make the wireless connection this reducing the total available bandwidth to the connected clients to the DIR-880L. That's why from what I've read, they said to use it as an access point but to turn off DHCP so the main router has the IP assigning duties.
 

Raz0rEdge

Well-known member
Staff member
Moderator
Joined
Jul 17, 2009
Messages
15,745
Reaction score
2,071
Points
113
Location
MA
Your Mac's Specs
2022 Mac Studio M1 Max, 2023 M2 MBA
The various router modes have not a lot to do with bandwidth but more about how the data is routed. So in bridge mode, the router that bridged basically says I'm just a conduit for all the traffic to someone above them and will just blindly forward. This means that you don't end up with a whole new network for the devices. If you are in AP/router modes then you end up with a whole new network that needs to be forwarded to the upstream router.

So for extending networks, you ideally want bridge mode so that the router will use it's WiFi access to get new devices onto a single network.

This should have no impact on bandwidth in any way.
 
Joined
Sep 2, 2018
Messages
17
Reaction score
1
Points
3
Bridge mode will allow that device to basically pass all internet connections onto another device that can be used as an AP. Usually cable modems that double as routers have this setting.
 

Shop Amazon


Shop for your Apple, Mac, iPhone and other computer products on Amazon.
We are a participant in the Amazon Services LLC Associates Program, an affiliate program designed to provide a means for us to earn fees by linking to Amazon and affiliated sites.
Top