Results 1 to 4 of 4
  1. #1


    Member Since
    Jan 16, 2017
    Posts
    3
    iPod Car Charger w/ Audio Out
    I have been working on a circuit design that would allow me to charge my iPhone/iPod classic 120 GB from my car. I am going to use power from the back of the cigar lighter sockets and put it into this circuit.

    The plan is that it will step the voltage down the a usable charging voltage for the iPod. I have also had to use a voltage divider to provide power to the D+ and D- pins on the USB plug, apparently the phone will not charge with out it.

    There is also an audio out section there that will basically use the GND, L Audio and R Audio and this will be wired into a 3.5 mm plug to go to my car sound system. There is also a 1 M Ohm resistor going from pin 21 on the iPod to GND to tell the iPod to shutdown when power is lost.

    I am unable to breadboard this ATM as I don't have the voltage regulator or any rated capacitors. I have drawn up the breadboard design with Fritzing (see below). Now to the question, can anyone see any issues with my design? I am a little worried about how hot the LM7805 will get and also concerned about if the common ground is going to mess with my audio? For reference here is the iPod Pin out.

    Breadboard layout Breadboard layout

    Schematic Schematic

    Parts list

    12-14v power Car Battery
    C1 4.7uF 50V Electrolytic Capacitor
    C2 0.1uF 50V Electrolytic Capacitor
    J1 Generic female header - 10 pins (Ipod)
    J2 Generic female header - 3 pins (Audio)
    LM7805 LM7805
    R1 1MΩ Resistor
    R2 47kΩ Resistor
    R3 47Ω Resistor
    R4 150kΩ Resistor
    R5 100kΩ Resistor
    PCB layout PCB layout

  2. #2


    Member Since
    Jul 02, 2017
    Location
    New Hampshire
    Posts
    53
    Specs:
    2017 MacBook Air
    I assume you found an electronic's forum to post this on.. If not let me know. I know a site with some pretty smart folks in it that may be able to assist.

    Uncertain of the rules of posting another site, so PM me and I'll pass it.

  3. #3


    Member Since
    Oct 16, 2010
    Location
    Brentwood Bay, BC, Canada
    Posts
    6,136
    Urrr…hmmmm…???

    Do I dare ask why you don't just buy one that's already been made, and often complete with cables, and often just for a few dollars at your locals "Dollar Den" type store???

    They sure work well with our iPhone/iPods.






    - Patrick
    ======

  4. #4


    Member Since
    Jul 02, 2017
    Location
    New Hampshire
    Posts
    53
    Specs:
    2017 MacBook Air
    The fun part Patrick, is in the build! Reality, most store bought don't do what you really want.

    Example is I have a voltage regulator on a solar pump I use in my Soaker Tub. Yes, I could buy it on Amazon for $20. Cheap enough.. What I would buy doesn't give me what I really want, close, but...
    For $1.95 I bought the module and wired it myself. I have what I want.

    Now, I did buy the solar charge controller cause the build was more than what I wanted to do. $10 was cheap enough to sway me!

    Sometimes, it's all in the build!

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. best in iPhone/iPod car charger and FM transmitter?
    By space_invader64 in forum iPhone Hardware and Accessories
    Replies: 2
    Last Post: 06-28-2008, 05:17 PM
  2. iPod Shuffle Car Charger – is there a difference?
    By immdb in forum iPod Hardware and Accessories
    Replies: 2
    Last Post: 05-11-2005, 03:20 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •