Results 1 to 5 of 5
  1. #1


    Member Since
    Oct 14, 2010
    Location
    South Coast of England
    Posts
    9
    Specs:
    iMac 27" i5 Quad Core 2.8 GHz, OSx 10.6.4 and Windows 7 Pro.
    Unhappy Printing Problems under Boot Camp
    I have both OSx 10.6.4 and Windows 7 Pro operating on two Boot Camp partitions..
    Both work fine but I cannot print from the Windows side.
    I've tried re-installing the Printer drivers a couple of times, nothing adverse shows up in Device Manager either.

    But every time I try to print a Windows document a get a conflict which results in Windows wanting to send a Report back to Microsoft and then closing down the printing operation..

    Printer was supplied with both Mac and Windows installation Disks.
    As I say no Installation problems on either system but only the Mac Partition will Print correctly

    All-in-One Printer/Scanner/Copier is Kodak E3
    (I know it's a cheap rubbishy Printer but I don't do a lot of Printing)

    Any remedies anyone ??

  2. #2

    chscag's Avatar
    Member Since
    Jan 23, 2008
    Location
    Fort Worth, Texas
    Posts
    48,479
    Specs:
    Late 2013 27" iMac, iPad 3, iPhone 6s+, iPhone 6+, 3 iPods, El Capitan
    Post the exact error you're getting when trying to print. Perhaps we can figure something out. I assume you have the latest drivers installed from Kodak?

    Also, are you sure the printer designation is E3? I could not find anything relating to that model. Might it be a Kodak ESP 3?

  3. #3


    Member Since
    Oct 14, 2010
    Location
    South Coast of England
    Posts
    9
    Specs:
    iMac 27" i5 Quad Core 2.8 GHz, OSx 10.6.4 and Windows 7 Pro.
    Quote Originally Posted by chscag View Post
    Post the exact error you're getting when trying to print. Perhaps we can figure something out. I assume you have the latest drivers installed from Kodak?

    Also, are you sure the printer designation is E3? I could not find anything relating to that model. Might it be a Kodak ESP 3?
    The exact Printer/Scanner/Copier is ESP3 (Sorry)..

    I cannot print from any program, each program throws up it's own error message but they are all "conflicts".
    Everytime the error message appears it closes down the loaded program..
    I'll give you a couple of examples trying to print fron EditPadLite..

    First error message to appear when I press the print command from the Menu Bar....

    Access violation at address 06A05825 in module "EKIJ5000RRS.DLL".
    Read of address 00000000...

    I press OK on the error message and a second error message appears....

    Access violation at address 004BCC0C in module "EditPadLite.exe".
    Read of address 000002E4

    I then press OK and EditPad Lite closes down and leaves me on the Desktop.

    This happens with a variety of error message quotes depending on which program I am trying to print from at the time.....

    Yes, I've downloaded the very latest firmware and drivers for the ESP3..
    As I stated previously, everything installs without errors, Device Manager does not show up any defects or driver conflicts..

    This problem has only arisen since I started using my Windows 7 with Boot Camp, so I'm assuming it's some kind of conflict caused by Boot Camp..

    Thanks for helping, would appreciate any advice you can muster...
    Ron.

  4. #4


    Member Since
    Oct 14, 2010
    Location
    South Coast of England
    Posts
    9
    Specs:
    iMac 27" i5 Quad Core 2.8 GHz, OSx 10.6.4 and Windows 7 Pro.
    Printer Problem Solved
    I seemed to have solved the problem as follows :-

    1) Completely un-installed ALL Kodak Software..
    2) Manually removed ALL references and entries relating to "Kodak" from the Windows Registry..
    3) Shutdown and re-started Windows..
    4) Downloaded (again) the latest ESP-3 Software and Drivers from the Kodak Support site.
    5) Re-Installed the newly downloaded Kodak Software.

    Everything now seems to be printing OK under Windows in Boot Camp..

    My apologies to Boot Camp for any previous rash statements and/or implications of shortcomings, it was all my fault, something I didn't do correctly in the original Kodak install/update !!
    Thanks for any help anyway...
    Ron..

  5. #5

    chscag's Avatar
    Member Since
    Jan 23, 2008
    Location
    Fort Worth, Texas
    Posts
    48,479
    Specs:
    Late 2013 27" iMac, iPad 3, iPhone 6s+, iPhone 6+, 3 iPods, El Capitan
    OK, great. Glad to hear you got it working. I was going to suggest the exact same thing as you did and to download newer drivers. Have fun and visit us often.

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Boot Camp Problems
    By DoubleForte in forum Switcher Hangout
    Replies: 3
    Last Post: 03-11-2011, 09:18 AM
  2. Boot Camp Problems.
    By ryanclancy000 in forum OS X - Apps and Games
    Replies: 1
    Last Post: 01-14-2010, 04:33 PM
  3. Problems with Boot Camp and XP
    By Buckieluva1612 in forum Running Windows (or anything else) on your Mac
    Replies: 1
    Last Post: 05-24-2009, 10:01 AM
  4. Problems with boot camp
    By fantom4 in forum Apple Desktops
    Replies: 3
    Last Post: 07-18-2008, 07:27 AM
  5. Boot Camp Problems
    By Bordman in forum Running Windows (or anything else) on your Mac
    Replies: 1
    Last Post: 06-26-2008, 03:46 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •